> Draft Equipment >

Keg Master Series 4 Kegerator Dual Tower Complete Kit (with USED Pin Lock Cornelius Kegs)

Alternative Views:

Introducing the all new Keg Master Series 4 Kegerator Dual Tower Complete Kit!

For the first time OBK is offering kegerator kits that come fully equipped. These kegerator units use commercial quality well known dispensing equipment that other kegerators can't hope to match.

It is fully upgradable so you can choose your faucets, tower, regulator, and co2 tank right from the start! Save money and get what you want right away without having to retrofit a standard kegerator kit to fit your needs.

All of our Kegerators come equipped with a high quality Taprite regulator as well as CM Becker disconnects.

This complete kit comes with all required equipment and 2 Pressure Tested Used 5 Gallon Pin Lock Cornelius Kegs (used kegs require cleaning and sanitizing).

Kegerator Fridge Features:

New and improved Font Fan
New Circuit Boards with temperature control, calibration, and on-board memory functions
Sturdy guard rail system
Increased compressor power while being approximately 20% more electrically efficient
Improved drip tray & rear cylinder bracket holder
Glass holder and wire shelf

*New (Empty) Luxfer Aluminum CO2 Tank is Optional

Please Note:

Due to the highly customizable nature of these Kegerators there are many ways for them to be assembled. As such the below instructions are meant to be a very basic guide to assembling your Kegerator and may not match 100% based on what products are chosen for your kit.
We will contact you regarding shipping.
The Taprite S.S Beer Tower - Double Faucet (upgrade) comes with Wing Nut Connectors attached to the beer lines. They will need to be removed prior to use with any disconnects.

Price: $899.99

Price with Selected Options: $899.99

Availability: Usually Ships in 24 Hours

Tower Option

CO2 Tank Options

Regulator

Free Faucet (Upgradable)

Second Free Faucet (Upgradable)

Choose Your Tap Handles

Add a Faucet Wrench

Quantity:

Features

Instructions

Keg Master Series 4 Kegerator Dual Tower Complete Kit (with USED Pin Lock Cornelius Kegs)

Kit Includes:

Keg Master Series 4 Kegerator Kit
Co2 Tank Holder (Maximum of 5lb Co2 Tank)
Taprite Primary CO2 Regulator (Poly Bonnet, 60PSI & 2000PSI) [T742HP-02]
6' of Bevlex 200 Beer Line (Thick wall 3/16" ID x 7/16" OD) for each tap
4' of Ultraflex Gas Tubing (5/16" ID x 9/16" OD) for each gas connection
Pin Lock MFL Threaded Gas & Beverage CMBecker Disconnects
Stainless Steel Swivel Nuts (1/4" Barb for Beverage, 5/16" Barb for Gas)
Stainless Steel Dual Tap Beer Tower with Mounting Hardware (OPTIONAL Upgrade)
Chrome Plated Faucets with Tap Handles (OPTIONAL Upgrade)
Commercial Grade 2 Way Gas Distributor (Manifold)
1/4" MFL to 1/4" MFL Cooler wall Bulkhead Adapter - 4" Long
Stainless Steel Hose Clamps
2 Pressure Tested Used 5 Gallon Pin Lock Cornelius Kegs (used kegs require cleaning and sanitizing) - 304 Stainless Steel

Exterior Dimensions:

Depth (with Co2 Holder): 31 1/4"
Depth (no Co2 Holder): 25"
Width: 24"
Height (no Wheels, Tower, or Rails): 32 1/2"
Height (with Tower): 47 3/4"

Interior Dimensions:

Height: 28 3/8"
Width: 20 1/2
Depth: 16 1/4"
Depth (Minus Bottom Step): 13 1/4"

Shipping Dimensions:

Height: 36"
Width: 28"
Depth: 28"

To put together your Kegerator unit simple follow these steps:

Exterior Installation Instructions:

Remove the black cap at the top of the fridge and secure your tower to the fridge allowing the beverage lines to go into the fridge.
Go to the rear of the fridge and remove the black cap.
Find the Co2 bulkhead adapter and install it into the open hole (the inside of the fridge is a tight fit so you may need to remove the font fan prior to installing the bulkhead adapter).
Once installed take one of the gas lines and put the included clamp on the hose and insert one of the 5/16" swivel nuts into the tubing. Tighten the clamp to secure the swivel nut.
Take the two gas lines from the prior step and attach it to the exterior portion of the Co2 bulkhead (make sure to have a flared washer between the swivel nut and Co2 bulkhead).

Interior Installation Instructions:

With the exterior portion complete now it is time to install the interior hardware/equipment
Grab one of the other gas lines and put the included clamp on the hose and attach it to the 'inlet' barbed portion of the manifold. Tighten the clamp.
Using the prior gas line attach the opposite end to the interior portion of the Co2 bulkhead (make sure to have a flared washer between the swivel nut and Co2 bulkhead). Please Note: This step can be tricky, it is recommended that you remove the font (tower) fan to make this step easier.
Once installed take one of the remaining gas lines and put the included clamp on the hose and attach it to one of the 'outlet' barbed portions of the manifold. Tighten the clamp. Do this twice.
Find your two gas disconnects and thread them onto the gas lines.
Take the two beverage lines and put one of the included hose clamps on each of them and insert the included 1/4" swivel nuts into the tubing. Tighten the clamps.
With these lines attach them to the included beverage disconnects.
Attach the beverage and gas disconnects to your pin lock kegs.

Co2 Installation Instructions:

Take the Co2 tank holder and hang it on the exterior hanging pegs at the back of the fridge and set your Co2 tank onto it. Secure in place with the included strap.
Attach your Taprite regulator to the Co2 tank and attach the hanging gas line to it using the flared washer found in the Taprite box.
With that last step you are done and ready to dispense!

Keg Master Series 4 Kegerator Dual Tower Complete Kit (with USED Pin Lock Cornelius Kegs)

Share your knowledge of this product with other customers... Click here to write a review

Share your knowledge of this product with other customers...
Click here to write a review