> Brewing Equipment >

Stainless Steel Weldless Spigot Kit (2 Piece)
Stainless Steel Weldless Spigot Kit for Mash Tun
Installing a spigot kit on a brew kettle is an easy and convenient way to drain liquid from the kettle without having to pour the wort manually over the strainer or siphoning it. This is extremely helpful especially when working with large batches of brew.

This stainless steel weldless spigot kit is designed to have a solid leak-free connection. Made from 100% industrial-grade stainless steel, the mini ball valve can withstand high heat and is resistant to rust and corrosion. Home brewers can use it for a long time without any problem.

It also features a 1/2" two-piece ball valves and an optional barb to easily attach a silicone hose. It also comes with a full coupler that is added to the back of the spigot to allow home brewers to add any accessories with a 1/2" male NPT fitting.

The spigot kit can be easily installed to the brew kettle after drilling a hole using a 7/8" drill bit. When drilling the hole, constantly add water to the area to prevent it from heating up which can damage the brew kettle. To address the issue of leaks and for a tight and leak-free seal, the spigot kit comes with a bulkhead fitting.

This stainless steel spigot kit is a great accessory to maximize a homebrew kettle by allowing brewers to create a constant flow of the liquid for efficient drainage.
Price: $29.99
Sale Price: $17.49
Save $12.50!

Availability: Usually Ships in 24 Hours

Choose Barb Size

1/2" Barb
3/8" Barb


Stainless Steel Weldless Spigot Kit (2 Piece)

  • Made from 100% stainless steel for added durability

  • Comes with a 1/2" two-piece ball valve with optional 3/8" or 1/2" barb

  • Full coupler added in the back of the valve to allow the addition of any 1/2" male NPT fittings

  • Comes with a bulkhead fitting for a watertight seal

Average Customer Review: Average Customer Review: 4.5 of 5 4.5 of 5 Total Reviews: 4 Write a review.

  0 of 0 people found the following review helpful:
5 of 5 Perfect for a weldless keggle June 26, 2015
Reviewer: Chris from Kitchener, ON Canada  
I installed this yesterday. Unfortunately, I only had a step bit that went up to 3/4", which wasn't quite big enough. But I was able to expand the opening slightly with a half-round bastard file and then it was a perfect fit. It only took about 5 more mins.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
5 of 5 Fantastic! May 5, 2014
Reviewer: Sam  
A great cost effect alternative for a keggle conversion!

Was this review helpful to you?

  1 of 1 people found the following review helpful:
4 of 5 Works like a charm April 16, 2014
Reviewer: Tom Whitaker from Innisfil, ON Canada  
Easy to install. buy a cheapo cantire step drill, drill it out, use rat tail file to enlarge further if req'd. Easy, no leaks, convert your pots to working kettles you will wonder why you waited so long its a snap.

Was this review helpful to you?

  2 of 2 people found the following review helpful:
4 of 5 Easy to use/install August 27, 2013
Reviewer: Marc Plante from Ottawa  
Bought two of these recently for my keggles. Ran a few 'water' tests through them before the first brew day, and found I have some small leakage. If you tighten them too much, the rubber fitting could get stripped, so be careful. Otherwise, these babies look great, easy to use, love the lock handle for safety, and very easy to install. This is a must if you don't know a welder.

Was this review helpful to you?