> Brewing Equipment >

Thru-Wall Bulkhead Fitting - Stainless Steel (1/2" Female NPT)
Thru-Wall Bulkhead Fitting - Stainless Steel
 
This kettle bulkhead is made using 304 stainless steel hardware, in addition it includes two high temperature silicone o-rings.

It is 1" in length and perfect for tighter spaces on brew pots and kettles. The maximum wall thickness is 3/8".

A pre-drilled hole that is 1" in size is required for installation.
Price: $12.49

Availability: Usually Ships in 24 Hours
Quantity:

Features
 

Thru-Wall Bulkhead Fitting - Stainless Steel (1/2" Female NPT)

Details:
  • Made out of 304 stainless steel
  • 3/4" NPT (exterior threading)
  • 1/2" NPT (interior threading)
  • Silicone o-rings x 2
  • Maximum wall thickness of 3/8"
  • Total length of 1"
  • Requires a pre-drilled hole that is 1" in size for installation

Measure before ordering.

May we also suggest...
Stainless Steel Thermometer 2" Probe Stainless Steel Close Nipple - 1/2" Male NPT x 1/2" Male NPT Stainless Steel 3 Piece Ball Valve - 1/2" Female NPT
Price: $19.99

Add
Price: $2.49

Add
Price: $20.99

Add
Stainless Steel Thermometer 2" Probe 304SS Stainless Steel Nipple 1/2" X 1" M NPT 3 Piece Stainless Steel Ball Valves

Average Customer Review: 4.5 of 5 Total Reviews: 4 Write a review.

  0 of 0 people found the following review helpful:
 
Not a great design... October 11, 2017
Reviewer: Justin A. from Guelph, ON  
The lock nut in this package is not grooved to hold the silicone o-ring nor does it have a large surface area, nor is a washer provided. As such it is a very delicate balance to tighten this without the o-ring being pushed out. Once this balance has been achieved, you may find this bulk head provides less support than what you had hoped since it can not be tightened very much. A second o-ring provides some leak insurance on the outside of the vessel, but shouldn't be necessary if the design were more reliable. If possible I suggest you trying to use a close nipple threaded into a ball valve (or whatever) with a grooved lock-nut and o-ring on the inside of your vessel, which should work a lot better. Lastly, I may be wrong, but at the time of writing this I think it's actually cheaper to buy the individual components here -
3/4" MPT x 1/2" FPT Reducer Bushing
3/4" NPT Lock Nut
Silicone O-Ring

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great bulkhead June 13, 2014
Reviewer: Adrian McManus from Hamilton, ON Canada  
I used this to finally replace the last piece of brass on my cooler mash tun. I already had a 1-1/8" hole drilled though it so the other weldless bulkheads sold by OBK left too much of a space. I got away with this one, even though it is designed for a 1" hole.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Perfect May 12, 2014
Reviewer: Sam Larkman from Bracebridge, ON Canada  
Worked perfectly for adding a fitting to the top of my BIAB system!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Excellent product April 22, 2014
Reviewer: Lorant Marton from Calgary, AB Canada  
This product fits a 1" diameter hole perfectly. it provides internal threads so you can fit an internal attachment and an external attachment.

I had a situation where I acquired two kegs that already had 1" holes drilled into it.

Was this review helpful to you?