Series X.1 Kegerator Single Tower Basic Kit | Pin Lock Cornelius

Series X.1 Kegerator Single Tower Basic Kit (Pin Lock Cornelius)

Write a Review

Status: In Stock

Available: 25

Quantity

Description
Instructions

NEW Series X.1 Model - More Power Efficient, Faster Cooling, and Better Insulation!

Introducing the all new Series X.1 Kegerator Single Tower Basic Kit!

For the first time OBK is offering kegerator kits that come fully equipped with duotight connections. Using all duotight hardware allows the use of a wide range of different components and easy system upgradability. All you need to provide is your own Co2 tank.

This Kegerator comes equipped with a Multi-Gas Co2 Regulator (100 PSI, 3000 PSI) [MK4] as well as beverage and gas disconnects. It has 8mm duotight connections that easily connect to the included Polyethylene Tubing.

This kit comes with all required hardware and equipment to attach a single pin lock keg. Kegs are NOT included.

Key Improvements (From Series X Kegerator):

10% More Energy Efficient
15% Faster Cooling and Improved Chilling in Warmer Climates
40% Thicker Walls for Improved Insulation
Interior Fridge Light for Better Visibility

Key Improvements (From Series 4 Kegerator):

30% Larger Evaporator
25% Larger Condenser

Kegerator Fridge Features:

New and improved Font Fan
New Circuit Boards with temperature control, calibration, and on-board memory functions
Sturdy guard rail system
Increased compressor power while being approximately 20% more electrically efficient
Improved drip tray & rear cylinder bracket holder
Glass holder and wire shelf

Includes:

Series X.1 Kegerator
Co2 Tank Holder (Maximum of 5lb Co2 Tank)
Multi-Gas Co2 Regulator (100 PSI, 3000 PSI) [MK4]
Font Fan (toggle on/off)
CO2 Cylinder Bracket Holder
Guard Rail
Drip Tray
Stainless Steel Door
Black Reinforced Plastic Top
Reinforced Four Point Anchored Castor Wheels
Brushed Stainless Steel Single Faucet Beer Tower x 1
Stainless Steel Push-In Tower Shank Assembly - 1/4" (6.5mm) x 1
Nukatap Stainless Steel Beer Faucet x 1
Black Plastic Tap Handle x 1
Polyethylene Double Wall Tubing - 5/32" ID (4mm) X 5/16" OD (8mm) x 5'
Polyethylene Double Wall Tubing - 13/64" ID (5mm) X 5/16" OD (8mm) x 8'
Duotight Food Grade Plastic (Push-In) Straight Reducer - 1/4" (6.35mm) X 5/16" (8mm) x 1
Duotight Food Grade Plastic (Push-In) Fittings - 1/4" FFL X 5/16" (8mm) x 2
Pin Lock MFL Threaded Beverage Disconnect x 1
Pin Lock MFL Threaded Gas Disconnect x 1
5-in-1 Tap and Cylinder Tool x 1
Mounting Hardware
110V

Exterior Dimensions:

Depth (with Co2 Holder): 31 1/4"
Depth (no Co2 Holder): 25"
Width: 23 5/8"
Height (no Wheels, Tower, or Rails): 33 1/2"
Height (with Tower): 48 3/4"

Interior Dimensions:

Height: 28 3/8"
Width: 19 3/8"
Depth: 17 1/2"

Shipping Dimensions:

Height: 36"
Width: 29"
Depth: 26"

Series X.1 KEGERATOR INSTRUCTION MANUAL

To put together your Kegerator unit simple follow these steps:

Exterior Installation Instructions:

Remove the black cap at the top of the fridge and prepare the single tower for installation.
With the tower attach the included hardware including the tower shanks and the duotight reducers.
The reducers are to be attached to the tower shanks and the EVABarrier tubing, with the larger of the two push in fitting ends attaching to the tubing and the smaller end to the tower shanks.
Insert the 4mm x 8mm EVABarrier tubing section into the duotight push in fitting inside of the tower.
With one of the included FFL duotight fittings attach it to the other end of the EVABarrier tubing.
Continue by securing your tower to the fridge allowing the beverage line to go into the fridge.
Open up the fridge and remove the black cap inside and go to the rear and remove the other black cap.

Interior Installation Instructions:

With the exterior portion complete now it is time to install the interior hardware/equipment
Grab the 5mm x 8mm EVABarrier gas tubing portion and attach it to the other FFL duotight fitting.
Using the same gas line put the other end through the hole in the fridge. Please Note: It is recommended that you add some form of insolation around the gas line in the hole to ensure that the cold temperatures of the fridge do not escape. Doing so will cut down on energy consumption and ensure that the internal temperatures are maintained better.
Take the two duotight fittings that are attached to the EVABarrier tubing lines and attach them to the included gas and beverage disconnects.
Attach the beverage and gas disconnects to your pin lock kegs.

Co2 Installation Instructions:

Take the Co2 tank holder and hang it on the exterior hanging pegs at the back of the fridge and set your Co2 tank onto it. Secure in place with the included strap.
Attach your MK4 Regulator to the Co2 tank and attach the gas line coming out of the fridge to it using the FFL duotight fitting that comes preinstalled on your MK4 Regulator.
With that last step you are done and ready to dispense!

Series X.1 Kegerator Single Tower Basic Kit (Pin Lock Cornelius)

NEW Series X.1 Model - More Power Efficient, Faster Cooling, and Better Insulation!

Mailing List